Exablaze: Setup and Test - Revision history

Chenhui: /* Driver Installation */

2015-01-12T09:27:21Z

Driver Installation

Chenhui: /* Driver Installation */

2015-01-12T09:10:11Z

Driver Installation

Chenhui: /* Driver Installation */

2015-01-08T17:27:48Z

Driver Installation

Chenhui at 17:12, 8 January 2015

2015-01-08T17:12:43Z

Chenhui at 17:11, 8 January 2015

2015-01-08T17:11:12Z

Chenhui: Created page with "== OS Detection == After the clean CentOS installation, the OS is able to detect the existence of the card: [root@localhost ~]# lspci|grep -i exan 87:00.0 Ethernet con..."

2015-01-08T17:03:06Z

Created page with "== OS Detection == After the clean CentOS installation, the OS is able to detect the existence of the card: <syntaxhighlight> [root@localhost ~]# lspci|grep -i exan 87:00.0 Ethernet con..."

New page

== OS Detection ==
After the clean CentOS installation, the OS is able to detect the existence of the card:
<syntaxhighlight>
[root@localhost ~]# lspci|grep -i exan
87:00.0 Ethernet controller: Exablaze ExaNIC X2
</syntaxhighlight>

@@ Line 20: / Line 20: @@
 #: <syntaxhighlight> exanic-config exanic0 </syntaxhighlight>
 #: The output should be something like:
-<blockquote>
   Device exanic0:
    Hardware type: ExaNIC X2
@@ Line 49: / Line 50: @@
      RX packets: 0  ignored: 0  error: 0
      TX packets: 0

@@ Line 20: / Line 20: @@
 #: <syntaxhighlight> exanic-config exanic0 </syntaxhighlight>
 #: The output should be something like:
   Device exanic0:
    Hardware type: ExaNIC X2
    Board ID: 0x02
    Temperature: 61.4 C   VCCint: 1.01 V   VCCaux: 1.83 V
-   Fan speed: 6807 RPM
+   Fan speed: 6807 RblockquotePM
    Function: network interface
    Firmware date: 20140709 (Wed Jul  9 04:30:36 2014)
@@ Line 48: / Line 49: @@
      RX packets: 0  ignored: 0  error: 0
      TX packets: 0

@@ Line 14: / Line 14: @@
 #: <syntaxhighlight> make</syntaxhighlight>
 #: <syntaxhighlight> make install </syntaxhighlight>
+#: Note: By default, the library will be installed to /usr/local/lib/libexanic.a, include files to /usr/local/include/exanic and utilities to /usr/local/bin/exanic-*. (You can add a  EFIX= argument to the make install command to use a prefix other than /usr/local.) Additionally the driver (exanic.ko) will be installed into /lib/modules/`uname  `/extra. If the driver fails to build, ensure that you have the kernel headers package for your kernel installed (this is typically named kernel-devel [RedHat/CentOS] or inux-headers [Debian/Ubuntu]).
-Note: By default, the library will be installed to /usr/local/lib/libexanic.a, include files to /usr/local/include/exanic and utilities to /usr/local/bin/exanic-*. (You can add a  EFIX= argument to the make install command to use a prefix other than /usr/local.) Additionally the driver (exanic.ko) will be installed into /lib/modules/`uname  `/extra. If the driver fails to build, ensure that you have the kernel headers package for your kernel installed (this is typically named kernel-devel [RedHat/CentOS] or inux-headers [Debian/Ubuntu]).
+# load the exanic module

← Older revision		Revision as of 17:12, 8 January 2015
Line 14:		Line 14:
	#: <syntaxhighlight> make</syntaxhighlight>		#: <syntaxhighlight> make</syntaxhighlight>
	#: <syntaxhighlight> make install </syntaxhighlight>		#: <syntaxhighlight> make install </syntaxhighlight>
		+
		+	Note: By default, the library will be installed to /usr/local/lib/libexanic.a, include files to /usr/local/include/exanic and utilities to /usr/local/bin/exanic-*. (You can add a EFIX= argument to the make install command to use a prefix other than /usr/local.) Additionally the driver (exanic.ko) will be installed into /lib/modules/`uname `/extra. If the driver fails to build, ensure that you have the kernel headers package for your kernel installed (this is typically named kernel-devel [RedHat/CentOS] or inux-headers [Debian/Ubuntu]).

← Older revision		Revision as of 17:11, 8 January 2015
Line 5:		Line 5:
	87:00.0 Ethernet controller: Exablaze ExaNIC X2		87:00.0 Ethernet controller: Exablaze ExaNIC X2
	</syntaxhighlight>		</syntaxhighlight>
		+
		+	== Driver Installation ==
		+	# go to http://exablaze.com/support/?serial=643f5f0123f8 and download the ExaNIC X2 Driver
		+	# untar the file
		+	#: <syntaxhighlight> tar xvzf exanic-1.4.2.tar.gz </syntaxhighlight>
		+	# build the driver from source
		+	#: <syntaxhighlight> cd exanic-1.4.2 </syntaxhighlight>
		+	#: <syntaxhighlight> make</syntaxhighlight>
		+	#: <syntaxhighlight> make install </syntaxhighlight>