Linux: IPTables - Revision history

Michael: /* Table Types (-t) */

2013-08-17T18:33:42Z

Table Types (-t)

2013-08-17T18:30:47Z

Table Types (-t)

2013-08-17T18:29:58Z

Table Types (-t)

2013-08-17T18:29:17Z

Table Types (-t)

2013-08-17T18:23:50Z

Table Types (-t)

2013-08-17T18:22:57Z

Table Types (-t)

2013-08-17T18:21:31Z

Starting and Stopping IPTABLES

2013-08-17T18:20:16Z

IPTables Rules

2013-08-17T17:47:21Z

Table Types (-t)

2013-08-17T17:46:17Z

IPTables Rules

@@ Line 33: / Line 33: @@
 There are two table types that can be used:  filter and nat.  The filter type is used by default is the -t flag is not used. The rules can be edited using the iptables command, system-config-firewall command or manually added to the /etc/sysconfig/iptables file.
 *[[IPTables: Filtering | Filtering Rules using the iptables command]]
 *[[IPTables: NAT| NAT Rules using the iptables command]]
 *[[IPTables: System_config_firewall | System-Config-Firewall]]

@@ Line 32: / Line 32: @@
 === Table Types (-t) ===
-There are two table types that can be used:  filter and nat.  The filter type is used by default is the -t flag is not used.
+There are two table types that can be used:  filter and nat.  The filter type is used by default is the -t flag is not used. The rules can be edited using the iptables command, system-config-firewall command or manually added to the /etc/sysconfig/iptables file.
 *[[IPTables: Filtering | Filtering Rules using the iptables command]]
 *[[IPTables: NAT| NAT Rules using the iptables command]]
 *[[IPTables: System_config_firewall | System-Config-Firewall]]

← Older revision		Revision as of 18:29, 17 August 2013
Line 38:		Line 38:
	*[[IPTables: Filtering \| Filtering Rules using the iptables command]]		*[[IPTables: Filtering \| Filtering Rules using the iptables command]]
	*[[IPTables: NAT\| NAT Rules using the iptables command]]		*[[IPTables: NAT\| NAT Rules using the iptables command]]
		+	*[[IPTables: System_config_firewall \| System-Config-Firewall]]

@@ Line 33: / Line 33: @@
 There are two table types that can be used:  filter and nat.  The filter type is used by default is the -t flag is not used.
 *[[IPTables: Filtering | Filtering Rules using the iptables command]]
 *[[IPTables: NAT| NAT Rules using the iptables command]]

@@ Line 34: / Line 34: @@
 There are two table types that can be used:  filter and nat.  The filter type is used by default is the -t flag is not used.
-*[[IPTables: Filtering | Filtering Rules]]
+*[[IPTables: Filtering | Filtering Rules using the iptables command]]
-*[[IPTables: NAT| NAT Rules]]
+*[[IPTables: NAT| NAT Rules using the iptables command]]

← Older revision		Revision as of 18:22, 17 August 2013
Line 35:		Line 35:

	*[[IPTables: Filtering \| Filtering Rules]]		*[[IPTables: Filtering \| Filtering Rules]]
−	*[[IPTables: ~~Filtering~~ \| NAT Rules]]	+	*[[IPTables: NAT\| NAT Rules]]

@@ Line 19: / Line 19: @@
 service iptables {start|stop|restart|condrestart|status|panic|save}
 </syntaxhighlight>
 == IPTables Rules ==

← Older revision		Revision as of 18:20, 17 August 2013
Line 10:		Line 10:

	Each packet contains the data to be sent, and administrative information including the source, destinations and type of data. IPTables examines this information to determine if the packet should be sllowed to pass.		Each packet contains the data to be sent, and administrative information including the source, destinations and type of data. IPTables examines this information to determine if the packet should be sllowed to pass.
		+
		+	== Starting and Stopping IPTABLES ==
		+
		+	IPtables can be started, stopped and reset using the services command, or through init.d
		+
		+	<syntaxhighlight>
		+	/etc/init.d/iptables {start\|stop\|restart\|condrestart\|status\|panic\|save}
		+	service iptables {start\|stop\|restart\|condrestart\|status\|panic\|save}
		+	</syntaxhighlight>
		+

	== IPTables Rules ==		== IPTables Rules ==