Mellanox:Ethernet Switch Configure VLANs - Revision history

David: /* Removing a VLAN */

2015-02-19T11:48:59Z

Removing a VLAN

David: /* Setting all the ports to hybrid and all VLANs */

2015-02-12T16:00:38Z

Setting all the ports to hybrid and all VLANs

David: /* Show all the VLAN Interfaces */

2015-01-21T15:51:57Z

Show all the VLAN Interfaces

David at 23:41, 20 January 2015

2015-01-20T23:41:27Z

David at 23:31, 20 January 2015

2015-01-20T23:31:25Z

Show changes

David at 22:39, 20 January 2015

2015-01-20T22:39:07Z

David: Created page with "This setup was used for Piston Coud, multiple VLANs routing between each other on the same switch. == Setup VLANs on SX1024 == Default username and password: admin/admin
2015-01-20T22:28:20Z

Created page with "This setup was used for Piston Coud, multiple VLANs routing between each other on the same switch. == Setup VLANs on SX1024 == Default username and password: admin/admin <b..."

New page
This setup was used for Piston Coud, multiple VLANs routing between each other on the same switch.

== Setup VLANs on SX1024 ==
Default username and password: admin/admin

<syntaxhighlight>
HPC-10GB [standalone: master] > enable
HPC-10GB [standalone: master] # configure terminal
HPC-10GB [standalone: master] (config) # ip routing
HPC-10GB [standalone: master] (config) # vlan 13
HPC-10GB [standalone: master] (config vlan 13) # name services
HPC-10GB [standalone: master] (config vlan 13) # exit
HPC-10GB [standalone: master] (config) # vlan 14
HPC-10GB [standalone: master] (config vlan 14) # name cloud
HPC-10GB [standalone: master] (config vlan 14) # exit
HPC-10GB [standalone: master] (config) # vlan 15
HPC-10GB [standalone: master] (config vlan 15) # name public
HPC-10GB [standalone: master] (config vlan 15) # exit
HPC-10GB [standalone: master] (config) # show vlan

VLAN Name Ports
---- ----------- --------------------------------------
1 default Eth1/1, Eth1/2, Eth1/3, Eth1/4, Eth1/5,
Eth1/6, Eth1/7, Eth1/8, Eth1/9, Eth1/10,
Eth1/11, Eth1/12, Eth1/13, Eth1/14, Eth1/15,
Eth1/16, Eth1/17, Eth1/18, Eth1/19, Eth1/20,
Eth1/21, Eth1/22, Eth1/23, Eth1/24, Eth1/25,
Eth1/26, Eth1/27, Eth1/28, Eth1/29, Eth1/30,
Eth1/31, Eth1/32, Eth1/33, Eth1/34, Eth1/35,
Eth1/36, Eth1/37, Eth1/38, Eth1/39, Eth1/40,
Eth1/41, Eth1/42, Eth1/43, Eth1/44, Eth1/45,
Eth1/46, Eth1/47, Eth1/48, Eth1/49, Eth1/50,
Eth1/51, Eth1/52, Eth1/53, Eth1/54, Eth1/55,
Eth1/56, Eth1/57, Eth1/58, Eth1/59, Eth1/60
13 services
14 cloud
15 public
HPC-10GB [standalone: master] (config) # interface vlan 13 ip address 192.168.2.1 255.255.255.192
HPC-10GB [standalone: master] (config) # interface vlan 13 no shutdown
HPC-10GB [standalone: master] (config) # interface vlan 14 ip address 192.168.3.1 255.255.255.0
HPC-10GB [standalone: master] (config) # interface vlan 14 no shutdown
HPC-10GB [standalone: master] (config) # interface vlan 15 ip address 192.168.4.1 255.255.255.192
HPC-10GB [standalone: master] (config) # interface vlan 15 no shutdown
</syntaxhighlight>

← Older revision		Revision as of 11:48, 19 February 2015
Line 363:		Line 363:
	HPC-10GB [standalone: master] (config) # interface vlan 5 no		HPC-10GB [standalone: master] (config) # interface vlan 5 no

		+	</syntaxhighlight>
		+
		+	== Setting up OSFP for Piston 3.6 ==
		+	<syntaxhighlight>
		+	switch-d15c16 [standalone: master] (config) # no spanning-tree
		+	switch-d15c16 [standalone: master] (config) # protocol ospf
		+	switch-d15c16 [standalone: master] (config) # router ospf
		+	switch-d15c16 [standalone: master] (config router ospf) # exit
		+	switch-d15c16 [standalone: master] (config) # interface vlan 103 ip ospf area 1
		+	switch-d15c16 [standalone: master] (config) # show ip ospf
		+
		+	Routing Process 1 with ID 172.16.3.1 vrf-default
		+
		+	Stateful High Availability is not supported
		+	Graceful-restart is not supported
		+	Supports only single TOS (TOS 0) route
		+	Opaque LSA not supported
		+	OSPF Admin State is enabled
		+	Redistributing External Routes: Disabled
		+	Administrative distance 110
		+	Reference Bandwidth is 40 Gbps
		+	Initial SPF schedule delay 1 msecs
		+	SPF Hold time 5000 msecs
		+	Maximum paths to destination 64
		+	Router LSA with maximum metric is not supported
		+	Condition: Always
		+	Number of external LSAs 0, checksum sum 0
		+	Number of opaque AS LSAs 0, checksum sum 0
		+	Number of areas is 1, 1 normal, 0 stub, 0 nssa
		+	Number of active areas is 1, 1 normal, 0 stub, 0 nssa
		+
		+	Area (0.0.0.1) (Active)
		+	Interfaces in this area: 1 Active Interfaces: 1
		+	Passive Interfaces: 0
		+	SPF Calculation has run 1 times
		+	This area is Normal area
		+	Number of LSAs: 1, checksum sum 37716
		+
		+	switch-d15c16 [standalone: master] (config) # show ip ospf interface
		+
		+	Interface Vlan is 103 Enabled, line protocol is Up
		+	IP address 172.16.3.1, Mask 255.255.255.0
		+	Process ID 1 VRF Default, Area 0.0.0.1
		+	OSPF Interface Admin State is enabled
		+	State DESIGNATED ROUTER, Network Type BROADCAST, Cost 10
		+	Transmit delay 1 sec, Router Priority 1
		+	No designated router on this network
		+	No backup designated router on this network
		+	Timer intervals (sec's): Hello 10, Dead 40, Wait 40, Retransmit 5
		+	No authentication
		+	Number of opaque link LSAs: 0, checksum sum 0
		+
	</syntaxhighlight>		</syntaxhighlight>

@@ Line 120: / Line 120: @@
 Not even sure if this is required
 <syntaxhighlight>
 interface ethernet 1/15
 switchport mode hybrid

@@ Line 103: / Line 103: @@
    Description: N/A
    Counters: Disabled
 </syntaxhighlight>

@@ Line 282: / Line 282: @@
    Description: N/A
    Counters: Disabled
 </syntaxhighlight>

@@ Line 42: / Line 42: @@
 HPC-10GB [standalone: master] (config) # interface vlan 15 ip address 192.168.4.1 255.255.255.192
 HPC-10GB [standalone: master] (config) # interface vlan 15 no shutdown
 </syntaxhighlight>