XCAT Network bonding setup - Revision history

David: /* Cumulus Switch Configuration */

2021-02-19T21:11:38Z

Cumulus Switch Configuration

David at 10:10, 23 December 2020

2020-12-23T10:10:30Z

David: /* Switch1 Interfaces File */

2020-12-23T10:05:08Z

Switch1 Interfaces File

David: /* Cumulus Switch Configuration */

2020-12-23T10:03:59Z

Cumulus Switch Configuration

David: Created page with "== Cumulus Switch Configuration ==

 # switch commands apt-get install vim hostnamectl set-hostname switch1 vim /etc/cumulus/.license systemctl restart switchd vim /etc/ne..."

2020-12-23T10:03:37Z

Created page with "== Cumulus Switch Configuration == <pre> # switch commands apt-get install vim hostnamectl set-hostname switch1 vim /etc/cumulus/.license systemctl restart switchd vim /etc/ne..."

New page

== Cumulus Switch Configuration ==
<pre>
# switch commands
apt-get install vim
hostnamectl set-hostname switch1
vim /etc/cumulus/.license
systemctl restart switchd
vim /etc/network/interfaces
ip a
net add bridge bridge ports swp1-22
net add bridge bridge vids 100,200
net add bridge bridge pvid 1
net pending
net commit
vim /etc/network/interfaces
net add interface swp14 bridge access 100
net add interface swp15 bridge access 100
net add interface swp16 bridge access 100
net add interface swp17 bridge access 100
net add interface swp14 link speed 1000
net add interface swp15 link speed 1000
net add interface swp16 link speed 1000
net add interface swp17 link speed 1000
net pending
net commit
net show clag

# here's the interfaces file on switch1
root@vscaler-switch1:~# cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

source /etc/network/interfaces.d/*.intf

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
auto eth0
iface eth0
address 192.168.2.2/24

auto peerlink
iface peerlink
bond-slaves swp21 swp22

auto peerlink.4094
iface peerlink.4094
clagd-peer-ip linklocal
clagd-priority 1000
clagd-sys-mac 44:38:39:FF:00:01

auto node001-int
iface node001-int
bond-slaves swp1
bridge-vids 200 201
clag-id 1
mtu 9000

auto node001-pub
iface node001-pub
bond-slaves swp5
bridge-access 201
clag-id 2
mtu 9000

auto node002-int
iface node002-int
bond-slaves swp2
bridge-vids 200 201
clag-id 3
mtu 9000

auto node002-pub
iface node002-pub
bond-slaves swp6
bridge-access 201
clag-id 4
mtu 9000

auto node003-int
iface node003-int
bond-slaves swp3
bridge-vids 200 201
clag-id 5
mtu 9000

auto node003-pub
iface node003-pub
bond-slaves swp7
bridge-access 201
clag-id 6
mtu 9000

auto node004-int
iface node004-int
bond-slaves swp4
bridge-vids 200 201
clag-id 7
mtu 9000

auto node004-pub
iface node004-pub
bond-slaves swp8
bridge-access 201
clag-id 8
mtu 9000

auto swp14
iface swp14
bridge-access 100
link-speed 1000

auto swp15
iface swp15
bridge-access 100
link-speed 1000

auto swp16
iface swp16
bridge-access 100
link-speed 1000

auto swp17
iface swp17
bridge-access 100
link-speed 1000

auto uplink
iface uplink
bond-slaves swp18
bridge-access 201
clag-id 9
link-speed 1000

auto bridge
iface bridge
bridge-ports peerlink node001-int node002-int node003-int node004-int node001-pub node002-pub node003-pub node004-pub swp9 swp10 swp11 swp12 swp13 swp14 swp15 swp16 swp17 uplink swp19 swp20
bridge-pvid 1
bridge-vids 100 200 201
bridge-vlan-aware yes

auto vlan200
iface vlan200
address 172.16.200.252/24
vlan-id 200
vlan-raw-device bridge
</pre>

← Older revision		Revision as of 10:10, 23 December 2020
Line 1:		Line 1:
		+	== ifcfg files on the host ==
		+	<pre>
		+	[root@node001 network-scripts]# cat ifcfg-bond0
		+	DEVICE=bond0
		+	TYPE=Bond
		+	NAME=bond0
		+	BONDING_MASTER=yes
		+	BOOTPROTO=none
		+	ONBOOT=yes
		+	NM_CONTROLLED=no
		+	BONDING_OPTS="mode=4 miimon=100 lacp_rate=1"
		+
		+	[root@node001 network-scripts]# cat ifcfg-bond0.200
		+	ONBOOT="yes"
		+	USERCTL="no"
		+	VLAN="yes"
		+	DEVICE="bond0.200"
		+	BOOTPROTO="static"
		+	IPADDR="172.16.200.1"
		+	NETMASK="255.255.255.0"
		+	NAME="bond0.200"
		+
		+	[root@node001 network-scripts]# cat ifcfg-bond0.201
		+	ONBOOT="yes"
		+	USERCTL="no"
		+	VLAN="yes"
		+	DEVICE="bond0.201"
		+	BOOTPROTO="static"
		+	IPADDR="197.243.57.5"
		+	NETMASK="255.255.255.0"
		+	NAME="bond0.201"
		+
		+	[root@node001 network-scripts]# cat ifcfg-bond1
		+	DEVICE=bond1
		+	Type=Bond
		+	NAME=bond1
		+	BONDING_MASTER=yes
		+	BOOTPROTO=none
		+	ONBOOT=yes
		+	NM_CONTROLLED=no
		+	BONDING_OPTS="mode=4 miimon=100 lacp_rate=1"
		+
		+	[root@node001 network-scripts]# cat ifcfg-enp59s0f0
		+	TYPE=Ethernet
		+	BOOTPROTO=none
		+	NAME=enp59s0f0
		+	DEVICE=enp59s0f0
		+	ONBOOT=yes
		+	NM_CONTROLLED=no
		+	IPV6INIT=no
		+	MASTER=bond0
		+	SLAVE=yes
		+
		+	[root@node001 network-scripts]# cat ifcfg-enp59s0f1
		+	TYPE=Ethernet
		+	BOOTPROTO=none
		+	NAME=enp59s0f1
		+	DEVICE=enp59s0f1
		+	ONBOOT=yes
		+	NM_CONTROLLED=no
		+	IPV6INIT=no
		+	MASTER=bond1
		+	SLAVE=yes
		+
		+	[root@node001 network-scripts]# cat ifcfg-enp94s0f0
		+	TYPE=Ethernet
		+	BOOTPROTO=none
		+	NAME=enp94s0f0
		+	DEVICE=enp94s0f0
		+	ONBOOT=yes
		+	NM_CONTROLLED=no
		+	IPV6INIT=no
		+	MASTER=bond1
		+	SLAVE=yes
		+
		+	[root@node001 network-scripts]# cat ifcfg-enp94s0f1
		+	TYPE=Ethernet
		+	BOOTPROTO=none
		+	NAME=enp94s0f1
		+	DEVICE=enp94s0f1
		+	ONBOOT=yes
		+	NM_CONTROLLED=no
		+	IPV6INIT=no
		+	MASTER=bond0
		+	SLAVE=yes
		+	</pre>
		+
		+
	== Cumulus Switch Configuration ==		== Cumulus Switch Configuration ==
	<pre>		<pre>

@@ Line 113: / Line 113: @@
 net commit
 net show clag
 </pre>

@@ Line 148: / Line 148: @@
 iface vlan200
     address 172.16.200.252/24
     vlan-id 200
     vlan-raw-device bridge
 </pre>

@@ Line 25: / Line 25: @@
 net commit
 net show clag
 # here's the interfaces file on switch1
 root@vscaler-switch1:~# cat /etc/network/interfaces