Difference between revisions of "XCAT Installation on Centos 7"

Latest revision as of 17:05, 15 February 2021

Base Level Setup

Note: Starting point Centos minimal 7 with networking in place and setup

We start by setting the hostname and disabling SElinux

setenforce 0
sed -i 's/SELINUX=enforcing/SELINUX=disabled/g' /etc/sysconfig/selinux 
yum -y install vim tmux wget rsyslog
systemctl enable rsyslog
systemctl start rsyslog

Setup naming and hosts file

Set the hostname

hostnamectl set-hostname deploy.dt.internal

Set the /etc/hosts file

# Ensure there is a /etc/hosts entry for the internal interface

192.168.102.253 deploy.dt.internal      deploy

Disable the firewall

systemctl disable firewalld
systemctl stop firewalld

Setup the software repos

yum -y install yum-utils
wget --no-check-certificate -P /etc/yum.repos.d https://xcat.org/files/xcat/repos/yum/latest/xcat-core/xcat-core.repo

yum -y install centos-release-stream
wget --no-check-certificate -P /etc/yum.repos.d https://xcat.org/files/xcat/repos/yum/xcat-dep/rh7/x86_64/xcat-dep.repo

Note: Centos repos also stored here, do not delete!

Add provisioning services on the headnode

yum -y install xCAT 
echo ". /etc/profile.d/xcat.sh" >> ~/.bashrc
source ~/.bashrc

Download CentOS

wget http://mirrors.ukfast.co.uk/sites/ftp.centos.org/7.9.2009/isos/x86_64/CentOS-7-x86_64-DVD-2009.iso

Define Compute image for provisioning

copycds ${iso_path}/CentOS-7-x86_64-DVD-1908.iso (where ${iso_path} is directory of the iso)

This file name must match the boot image from lsdef -t osimage

Enable ssh during the installation on the compute nodes

# enables ssh to the node during installation
chdef -t site clustersite xcatdebugmode=2
lsdef -t site clustersite

Enable the time service (Chronyd)

# add to the end of the file /etc/chrony.conf (note below for Indonesia, select correct tz)
echo "
server 1.id.pool.ntp.org
server 2.id.pool.ntp.org
server 3.id.pool.ntp.org
server 4.id.pool.ntp.org" >> /etc/chrony.conf

systemctl enable chronyd
systemctl start chronyd

Add a node to the installation

# add a node
# note: serialport=0 (ttyS0)
#       serialport=1 (ttyS1)
# replace each parameter with appropriate information
[root@deploy ~]# mkdef -t node node0001 groups=compute,all ip=192.168.102.10 mac=00:15:B2:AA:E2:60 netboot=xnba arch=x86_64 bmc=192.168.101.10 bmcusername=admin bmcpassword=admin mgt=ipmi serialport=0 serialspeed=115200 provmethod=centos7.9-x86_64-install-compute
1 object definitions have been created or modified.

# set the root password
chtab key=system passwd.username=root passwd.password=`openssl rand -base64 12`

# set the domain name
chdef -t site domain=dt.internal

Finalise the setup - below will create the /tftpboot files and /etc/hosts etc.

# finalise the setup 
# Complete network service configurations
makehosts
makenetworks 
makedhcp -n
makedns -n

Check the rcons status

# might not be needed systemctl enable goconserver
# systemctl start goconserver
makegocons
makegocons -q

Set the nodes to pxeboot

# Associate desired provisioning image for computes
nodeset compute osimage=centos7.9-x86_64-install-compute
rinstall nvme0001 osimage=centos7.9-x86_64-install-compute

Useful commands


# check the node stats
lsdef -t node -l
lsdef -o node0001

# check the operating systems stats 
lsdef -t osimage -o centos8-x86_64-install-compute

# change a node mac address
makedhcp -d <nodename>
chdef -t node -o  <nodename> mac=<new-mac>
makedhcp <nodename>
lsdef -o node001


# reinstall a node 
# currstate=boot
nodeset node0001 osimage=centos8-x86_64-install-compute
[root@deploy nets]# lsdef node0001 | grep currstate 
    currstate=install centos8-x86_64-compute

# using a console session - whats the root password? 
tabedit passwd

# setup RAID1 for the compute nodes
mkdir -p /install/custom/partition/
wget https://raw.githubusercontent.com/xcat2/xcat-extensions/master/partition/raid1_rh.sh -O /install/custom/partition/raid1_rh.sh

# Set the partition file as part of the provision
chdef -t osimage centos8-x86_64-install-compute partitionfile="s:/install/custom/partition/raid1_rh.sh"

# reprovision the node
rinstall node0001 osimage=centos8-x86_64-install-compute

# disk notes: check status of RAID array
cat /proc/mdstat
mdadm --detail /dev/mdX


# add a new node to an existing cluster