Difference between revisions of "Bright:Network settings"
Jump to navigation
Jump to search
(Created page with "=== DHCP === To enable DHCP on Bright Cluster, we need to make sure that the lockdowndhcp property is set for that network. <syntaxhighlight> # cmsh % network use <network_name> % set lo...") |
|||
| Line 1: | Line 1: | ||
| − | + | == DHCP == | |
To enable DHCP on Bright Cluster, we need to make sure that the lockdowndhcp property is set for that network. | To enable DHCP on Bright Cluster, we need to make sure that the lockdowndhcp property is set for that network. | ||
<syntaxhighlight> | <syntaxhighlight> | ||
| Line 14: | Line 14: | ||
% foreach -n node001..node010 (interfaces; use eth1; set network | % foreach -n node001..node010 (interfaces; use eth1; set network | ||
<new_network>; commit) | <new_network>; commit) | ||
| + | </syntaxhighlight> | ||
| + | |||
| + | == Change interface IP address == | ||
| + | <syntaxhighlight> | ||
| + | [root@bios-head ~]# cmsh | ||
| + | [bios-head]% device use master | ||
| + | [bios-head->device[bios-head]]% interfaces | ||
| + | [bios-head->device[bios-head]->interfaces]% use eth1 | ||
| + | [bios-head->device[bios-head]->interfaces[eth1]]% show | ||
| + | Parameter Value | ||
| + | -------------------------------- ------------------------------------------------ | ||
| + | Additional Hostnames | ||
| + | BringUpDuringInstall NO | ||
| + | Card Type Ethernet | ||
| + | DHCP no | ||
| + | IP 185.93.28.11 | ||
| + | MAC 00:30:48:C8:7A:DD | ||
| + | Network externalnet | ||
| + | Network device name eth1 | ||
| + | On network priority 60 | ||
| + | Revision | ||
| + | Speed | ||
| + | Start if ALWAYS | ||
| + | Type physical | ||
| + | [bios-head->device[bios-head]->interfaces[eth1]]% set ip 185.93.28.12 | ||
| + | [bios-head->device*[bios-head*]->interfaces*[eth1*]]% commit | ||
| + | [bios-head->device[bios-head]->interfaces[eth1]]% .. | ||
| + | [bios-head->device[bios-head]->interfaces]% .. | ||
| + | [bios-head->device[bios-head]]% .. | ||
| + | [bios-head->device]% .. | ||
| + | [bios-head]% .. | ||
| + | [root@bios-head ~]# reboot | ||
</syntaxhighlight> | </syntaxhighlight> | ||
Latest revision as of 15:58, 3 February 2016
DHCP
To enable DHCP on Bright Cluster, we need to make sure that the lockdowndhcp property is set for that network.
# cmsh
% network use <network_name>
% set lockdowndhcpd no
% commitPlease note that a node is attached to a network by attaching aninterface to this node which is connected to that network. If you want to change the network of some nodes, you can do that by changing the network property of the interfaces attached to those nodes using the commands below:
# cmsh
% device
% foreach -n node001..node010 (interfaces; use eth1; set network
<new_network>; commit)Change interface IP address
[root@bios-head ~]# cmsh
[bios-head]% device use master
[bios-head->device[bios-head]]% interfaces
[bios-head->device[bios-head]->interfaces]% use eth1
[bios-head->device[bios-head]->interfaces[eth1]]% show
Parameter Value
-------------------------------- ------------------------------------------------
Additional Hostnames
BringUpDuringInstall NO
Card Type Ethernet
DHCP no
IP 185.93.28.11
MAC 00:30:48:C8:7A:DD
Network externalnet
Network device name eth1
On network priority 60
Revision
Speed
Start if ALWAYS
Type physical
[bios-head->device[bios-head]->interfaces[eth1]]% set ip 185.93.28.12
[bios-head->device*[bios-head*]->interfaces*[eth1*]]% commit
[bios-head->device[bios-head]->interfaces[eth1]]% ..
[bios-head->device[bios-head]->interfaces]% ..
[bios-head->device[bios-head]]% ..
[bios-head->device]% ..
[bios-head]% ..
[root@bios-head ~]# reboot